KitchenAid KODE900HSS00 Double Wall Oven: Wiring Diagram Guide, Connectors, Relays and Components
We typed this up from the wiring diagram (part W10903419B, dated 05/18) that came with a KitchenAid built-in double wall oven, model KODE900HSS00. We found it on a call in Tarpon Springs, where the whole oven was dead. The sheet is marked for service technicians. We didn't copy the diagram itself, only what it tells you in a form that's easy to look up. Other KitchenAid and Whirlpool double ovens of the same family may use a similar sheet, but check the one that came with yours.
This is service technician information. The oven runs on 240 volts. If you're not trained for that, call a technician.
Rating
- 7.7 kW at 208 V, or 10.3 kW at 240 V, 60 Hz.
- The sheet draws all voltages as 120/240 VAC. If the oven is connected to 120/208 VAC, read 240 VAC as 208 VAC.
- The circuit is drawn in standby/off mode with the oven door closed.
- The pin assignments for the pigtail connectors are in the separate tech sheet, not on this wiring diagram.
Boards and how they connect
The oven has one display board and one control board for each oven, plus an expansion board.
| Part | What the diagram shows |
|---|---|
| Keypad | Plugs into the user interface (display board) at J1. |
| User interface (display board) | Gets power and communications through a 4-pin wide/power connector, W4, that runs to the control boards. This is the board with the screen and touch controls. |
| Upper Copernicus ACU | The control board for the upper oven. Connectors J8 (line power), P1 (5 pins, communications), P3 (sensors and switches), P4, P5 (fans and latch), P7 (lights), PX1, PX3 and PX4 (elements). |
| Lower Copernicus ACU | The control board for the lower oven. It has the same connectors and does the same job for the lower oven. |
| Expansion board | Takes power at J4 (4 pins) and talks to the control boards at J3 (5 pins). Its outputs J51 to J54 and J71 to J74 go to the powered accessory pigtail connector. |
| Powered accessory pigtail connector | A 9-pin connector. Pin 5 goes to chassis ground. |
| EOL | The end of line tester. The sheet says it is for manufacturing purposes only. |
What each control board runs
The upper and lower ovens are wired the same way, so this table applies to both. Each oven's own control board switches its own parts.
| Part | Switched by | Plugs in at |
|---|---|---|
| Broil element, 4000 W | Relay K11 | Connector PX4, pins 1 and 2 |
| Bake element, 2800 W | Relays K10 and K2 | Connector PX1 |
| Convection element, 3200 W | Relay K2 | Connector PX1 |
| Temperature limiter (non-resettable), opens at 338°F (170°C) | Relay K3 | Connector PX3, pins 1 and 2 |
| Oven lights | Triac TR1 | Connector P7 |
| Motor door latch | Relays K4, K6, K7 and K8 | Connector P5 |
| Convection fan | Control board | Connector P5 |
| Cooling fan, low speed (LS) | Control board | Connector P5 |
| Cooling fan, high speed (HS) | Control board | Connector P5 |
| Oven temperature sensor | Sensor input | Connector P3, pins 1 and 2 |
| Meat probe sensor | Sensor input | Connector P3, pins 3 and 4 |
| Motor latch switch | Switch input | Connector P3 |
| Door switch | Switch input | Connector P3 |
Reading the diagram
- Wire colors are abbreviated: BK black, WH white, RD red, BU blue, YL yellow, OR orange, GN green, BR brown, TN tan and V violet. Two codes with a slash, such as BK/WH, mean a striped wire.
- The legend covers ground, plug and receptacle connectors, light, AC drive motor, door switch, latch switch, heating element, relay contacts, an automatically resettable temperature limiter, a non-resettable thermal fuse, an enclosed thermistor, a non-resettable temperature limiter and a Hall effect sensor.
- The three vertical lines on each side are the power feed: N, L2 and L1.
When the whole oven is dead
This is our own reading of the diagram, not a procedure from the sheet. The display board gets its power and signal from the control boards through the W4 connector, and the keypad plugs into the display board. If the screen and keypad are dead, the power feed to the oven is fine and the display board is a suspect, but you'd want to confirm voltage at the connector before replacing anything.
Double oven that won't turn on or won't heat? We repair built-in ovens around Tarpon Springs, Palm Harbor, Clearwater and nearby. See our oven repair page or call(727) 599-9631.