Tech Sheets

GE 27-Inch Electric Wall Oven (ERC III Control): Error Codes F0 to FF, Sensor Test and Special Functions

We typed this up from the Technical Data Sheet (pub. no. 31-20276) for a 27-inch electric wall oven with an ERC III control and motorized door lock. It came with a GE wall oven from 1997 that we looked at in Dunedin:an F3 error, a loose temperature sensor and a discontinued control board. Other GE and Hotpoint ovens of the same era may use a similar sheet, but check the one that came with yours.

This is service technician information. The sheet says to disconnect power before servicing, and its warning says the components on the control are electrically hot when voltage is connected. If you're not trained for that, call a technician.

Error codes

This is our summary of the sheet's ERC failure code chart.

CodeMeaningDetailsCorrection
F0, F1, F7Stuck key padMay mean a relay is turned on.Find out whether the problem is the key panel or the control. Push CLEAR/OFF. Then disconnect the ribbon cable from the control and wait at least 32 seconds to see if the code comes back. If it comes back, the problem is in the control. If it doesn't, the problem is the key panel.
F2Oven over temperatureThe oven is over temperature in a cooking or clean mode. The control senses above 615°F with the door circuit in unlock mode, or above 915°F with the door locked. Also see the fan thermal switches.Look for welded relay contacts (heating elements on in off mode). Look for an open thermal switch in the lock motor circuit. It's normally closed and opens if the area overheats because the fan isn't running. Look for the cause: the fan thermal switch not closing, a stalled fan and so on. Look for high resistance in the sensor circuit from high contact resistance (poor terminal crimp, deformed terminals, a loose connection inside the sensor tube) or an intermittent solder joint. Also look for electrical noise in the sensor circuit (ham radio, cordless phone and so on).
F3, F4Open or shorted sensor circuitCould be a result of contamination on terminals, a pinched wire in the sensor circuit, or a cold solder joint on the control.Disconnect power to the range and remove the sensor from the oven (disconnect at the connector block). Measure sensor resistance at the control connector, taking care not to damage the terminals in the block. It should read 1100 Ω at room ambient (about 72°F). Measure each sensor lead from the connector block to ground. If shorted, look for a pinched or cut wire in the sensor circuit. Check the connector terminals for deformation or corrosion and repair or replace. If all of that is OK, replace the control.
F5Loss of relay drive circuitLoss of the relay drive circuit.Press Clear/Off and reprogram the control. If the F5 code reappears, replace the control. Check the sensor circuit. Check the lock motor circuit. If all of that checks OK, the F5 code can be the result of a momentary loss of power: do not replace the control and lock motor. Connections can be intermittent because of corrosive buildup between the connection and the terminals, or because they were bent by inserting a probe.
FCDoor lock circuit problemA problem with the door lock circuit, such as pinched wires between the control and the door lock switches on the motorized lock circuits.Check the wiring and test the operation of the switches.
FFLoss of door motor safety switchLoss of the door motor safety switch.Replace the control.

Oven sensor and door switch ohmmeter test

Remove power from the oven. Measure the resistance from the side of the sensor and lock switch connector, with the terminals exposed.

CircuitTerminalsOhms
Oven sensor4 to 61100 Ω at room temperature, 2600 Ω at clean temperature
Door unlatched1 to 30 Ω
Door latched2 to 30 Ω

If a reading looks abnormal, remove the sensor from the oven and check it at the disconnect block. Wiggle the leads while checking resistance. If it changes by more than 10 Ω, replace it.

Control voltage

BetweenVoltage
L1A and B to N120 VAC all the time
L1A and B to BAKE240 V when the oven is not calling for heat (bake and broil relay contacts open)
L1A and B to BROIL240 V when the oven is not calling for heat (bake and broil relay contacts open)
OV1 to N120 VAC when the light is off
AUX2 to N120 VAC while locking or unlocking

A temperature or mode has to be selected for the relay contacts to operate. Voltage must be present across L1 and N for the control to operate.

Heating elements

  • Bake element: 2000 W, about 29 Ω, 8.33 A.
  • Broil element: 3400 W, about 16.4 Ω, 14.2 A.
  • The bake and broil units cannot be on at the same time.
  • Bake and Time Bake: the bake unit only is on during preheat. After that the broil unit is on about 25% of the time during the rest of the bake operation.
  • Clean: the broil unit only is on for the first 30 minutes or until the oven reaches 750°F. During the rest of the clean operation, the oven cycles between the bake and broil units.

Key panel test

  • Press each pad on the key panel, followed by the CLEAR/OFF pad.
  • Bake, Broil, Clean, Timer, Clock and Cook Time: you hear an audible tone and the display shows the mode selected.
  • Clear/Off: an audible tone, and the display shows the time of day.
  • Temp, Hour and Min pads: no audible tone. They only work after another function has been selected.
  • If some pads work and some don't, the problem is probably the key panel.

To verify the key panel with an ohmmeter, set it to a high scale and connect the leads to the ribbon cable as shown in the sheet's chart for each function. Press the pad. The meter should read less than infinity (∞) Ω if the switch contact is working. If it reads ∞ when you press the pad, or shows some resistance without pressing it, the key panel is bad. Replacement touch pads come as part of the control panel.

FunctionRibbon cable conductors
BAKE12 to 14
BROIL11 to 14
CLEAN9 to 14
OVEN LIGHT9 to 13
COOKING TIME11 to 13
DELAY START TIME12 to 13
KITCHEN TIMER10 to 14
CLOCK10 to 13
CLEAR/OFF3 to 4
START1 to 2
UP TEMP6 to 13
DN TEMP6 to 14
UP HOUR7 to 13
DN HOUR7 to 14
UP MIN8 to 13
DN MIN8 to 14

Special functions

The control has a section you can enter to change how it works. Press and hold the BAKE and BROIL pads for 2 seconds, until SF appears in the display. Select the area to change. When the change has been made, press START to return to the time of day.

FunctionHow
End of cycle tonePress the Timer pad. The display shows Con Beep for a continuous end of cycle tone, or the non-continuous setting.
°F or °CPress the Broil pad. The display shows F° or C°. Press Broil again to change.
12 hour, 24 hour or blank clockPress the Clock pad. The display shows 12 hr, 24 hr or OFF for a blank clock.
Cook and HoldUsed only with Time Bake or Delay Bake. Press the Cooking Time pad. The display shows HLD On or Hld Off.
Child lockoutPress Clean. The display shows Loc ON (when any heating function is tried, the display shows OFF) and Loc Off when unlocked.
12 hour shut downComes set to shut down after 12 hours of continuous operation. To eliminate it, press Delay Start. The display shows No Shdn. To turn it back on, press Delay Start again and the display shows 12 Shdn.
Sales modeA special feature for sales floor demonstration. Press the Clock and Timer pads at the same time. The display cycles through the different modes of operation.

Oven calibration

The sheet says testing has shown this oven cooks best with a control setting of 350°F when the average center oven temperature is between 340°F and 380°F. A customer may change the average center oven temperature by up to ±35°F to suit their own cooking.

  1. Press and hold the Bake and Broil pads until SF appears in the display.
  2. Press the Bake pad to enter oven calibration mode. 00 or a number between ±35°F is displayed.
  3. Press the TEMP increase or decrease pads to change the average oven temperature. Use the Bake pad to switch between + and − settings.
  4. Press START to return to the time of day.

Motorized door lock

The motorized door lock assembly is above the oven. It consists of a lock motor cam, a lock switch assembly, a lock hook and a mounting plate.

  • The lock motor is energized when the control is set for Clean or Clean Time. The K4 relay contacts close and complete the circuit that supplies voltage to the lock motor.
  • The cam on the motor positions the lock hook in the door so it can't open during a clean cycle, and operates the two lock switches that tell the control if the door is locked and ready for clean.
  • When the door is being locked or unlocked, both lock switches 1 and 2 are in the open position.
  • The display flashes LOCK DOOR if the door switch is in the C to NC position. The word LOCK DOOR flashes on and off while the lock motor is moving. When the door is locked, the words LOCKED DOOR stay lit.

Thermal switches

  • A thermal switch is in the lock switch circuit, in the normally closed position. It's mounted on the rear wall of the control area. The limit switch opens at 216°F and closes when temperatures cool below 177°F.
  • The fan switch is a resettable switch on the floor of the component compartment. It turns the fan on in any mode of operation when it detects a temperature above 210°F, and the fan turns off once it has cooled below 161°F.

If the thermal switch opens:

  • With the oven below 600°F, in Bake or Broil the heating element cycles off, the lock motor runs and the word LOCK appears in the display with the cooking function and temperature. If the thermal switch closes while the lock motor is in the unlocking phase, the unit resumes cooking. If it closes while the lock motor is in the locking phase, the program is cancelled and the display returns to the time of day.
  • In Clean mode, the program is cancelled when the thermal switch opens.
  • With the oven above 600°F, any mode of operation goes to the F2 failure code. When this happens, check the fan operation (look for obstructions), inspect the oven installation (make sure the grill areas aren't blocked), and check the oven insulation and lock circuit.

Ground and power

  • Ground path resistance: 0.10 Ω maximum. Insulation resistance: 250 KΩ minimum.
  • The power supply cable is recognized for copper wire only, not aluminum wire.
  • The oven must be connected to a supply circuit of the proper voltage and frequency, as shown on the rating plate behind the oven door.

Maximum kilowatt rating by branch circuit fuse, for wall-mounted ovens:

NEC fuse rating208 V236 V240 V
20 Amp4.24.74.8
30 Amp6.27.17.2
35 Amp7.38.38.4
40 Amp8.39.49.6
50 Amp10.411.812.0

Door adjustment

  • Horizontal alignment of the door and control panel: add a U clip (part no. WB01K5078) to raise the door at the top, or file the hinge arm at the lower surface to lower the door.
  • Vertical alignment of the door to the front frame: add shim washers between the hinge plate and the front frame. To increase the gap at the top of the door, place the shim at screw A. To decrease it, place the shim at screw C.
  • Door spring tension can be lessened by moving the spring to a lower hinge position, or increased by moving it to a higher one. The sheet shows the spring hooks in the 3rd hole from the rear.

Oven showing an error code? We repair ovens and ranges around Dunedin, Palm Harbor, Clearwater and nearby, and we'll tell you honestly if it's worth fixing. See our oven repair page or call (727) 599-9631.